BendPak SP-7XEF Full-Rise Flush Mount Scissor Lift 7,000 lb.

The Full-Rise, Flush-Mount Scissor Lift
The SP-7XEF is the flush-mount version of our full-rise scissor lift. If your garage has a recessed area of concrete designed to hold flush-mount lifts, you’ll be pleased by how "invisible" this lift is in your garage. When it's collapsed, you’re free to drive over it and work around it without tripping on wires or cables. We’re proud that the collapsed SP-7XEF is extremely low-profile, but if you want to take low to virtually zero, the flush-mount version of this model is the perfect car lift solution for your garage.

Open-center Design
With 68" inches of lifting height and an open center, many mechanics have comfortable standing room to perform oil changes, transmission drops and an infinite number of other undercarriage services.

No Cross Member
The SP-7XEF is installed and mounted flush into your flooring without a cross member. This makes for a true open-center design that provides access to all critical undercarriage areas without requiring operators to stoop or crawl across the floor. Plus, there's less drilling into concrete, because space will only need to be made for the scissor structures—no longer for a cross member. Reinforced steel at the base and along the top of the runways help provide a stable lift that completely eliminates the need for that cross member or additional structural support.

Large Base Frame
The heavy-duty boxed-steel formed base frame increases stability and reduces stress on the overall structure. The elongated base provides a solid foundation for a smoother, perfectly level rise.

Electric / Hydraulic Power System
An electric hydraulic power system is kept in a rugged console box off to the side of the lift, safe from the lifting/lowering of the frames in and out of your flooring. The controls are easy to reach and allow you to keep an eye on your surroundings while lifting and lowering heavy vehicles.

Dual Master Hydraulic Cylinder
In order to push the frames out from a flush-mount position quickly and powerfully, the SP-7XEF is fitted with two hydraulic cylinders with flow restrictors to ensure an even lift. The controlled flow is sophisticated enough to prevent the risk of tipping, even if one cylinder loses pressure (due to an unlikely rupture or pinch, for instance). No emergency will result in the up-ending of your vehicle—the car lift would simply descend to the ground evenly on both frames.

Pneumatic Safety Locks
A single convenient operator stand allows you to release the pneumatic safety locks from a safe distance without ever worrying about manually lifting release arms or latches. The locks disengage when the lift lowers and automatically, and multiple locking positions provide operators with more service options. The locks engage or disengage at each position seamlessly with the movement of the scissor lift frames.

Hardened Pivot Pins with Zerk Fittings
Zerk grease fittings are self-lubricating and long-lasting, ensuring a smooth rise and descent of the lift platforms at all times.

Durable, Cushioned Rubber Contact Blocks
Hard rubber blocks set right atop the rubber padding on the lift platforms, safely and securely engaging vehicle pinch rails and OEM frame lift points.

Detailed Installation & Maintenance Instructions
An easy-to-read owner's manual offers complete installation instructions and maintenance tips, as well as safety/caution decals that come standard with every lift purchase.

• Flush-mount
• 7,000-lb. lifting capacity
• Pneumatic safety locks
• Hardened pivot pins with "Zerk" fittings
• Open-center design
• Ergonomic controls
• Dual-cylinder hydraulic design provides extra power
• Low-profile

Locking Heights*

• Fully Lowered: 6.5" (165 mm)
• 1st Lock: 24.75" (629 mm)
• 2nd Lock: 37.5" (953 mm)
• 3rd Lock: 46" (1,168 mm)
• 4th Lock: 52.75" (1,340 mm)
• 5th Lock: 58" (1,473 mm)
• 6th Lock: 62.75" (1,594 mm)
• 7th Lock: 66.5" (1,689 mm)
• 8th Lock: 70" (1,778 mm)
• Full Rise: 70.5" (1,791 mm)

*Heights measured from bottom of lift

*Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult www.autolift.org for a complete list.

LOW-RISE/MID-RISE LIFTS WARRANTY

Duration: From the date of purchase by the original Purchaser or 12-24 months from the date of shipment by BendPak or whichever comes first.

• Two Years (24-Months) Warranty on the lift structure
• One Year (12-Months) Warranty on the hydraulic cylinder(s) and power unit
• One Year (12-Months) Warranty on operating components
• One Year (12-Months) Labor Warranty on site or at factory
• One Year (12-Months) Free-Shipping* on ground-freight charges related to warranty performance

Limited Warranty

1. Who gives this warranty (Warrantor): BendPak Inc., 1645 Lemonwood Dr., Santa Paula, CA 93060
2. Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
3. What products are covered by this warranty: Any BendPak Full-Rise Scissor Lift**
4. What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
5. What is not covered under this warranty:
a. Any failure that results from Purchaser’s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner’s manual(s) supplied
b. Any damage caused by overloading lift beyond rated capacity
c. Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
d. Items considered general wear parts such as rubber pads, pad adapters, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
e. Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
f. Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
g. Rusted components due to improper maintenance or corrosive environments
h. Cosmetic defects that do not interfere with product functionality
i. Damage due to incorrect voltage or improper wiring
j. Any incidental, indirect, or consequential loss, damage, or expense that may result from any defect, failure, or malfunction of BendPak Inc. product
k. All electrical components are guaranteed for one year against defects in workmanship and/or materials when the lift is installed and used according to specifications. 6. Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
7. Responsibilities of Purchaser under this warranty:
a. Provide dated proof of purchase and maintenance records
b. In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
c. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
8. When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.

*Free-shipping applies to direct shipping points within the 48 continental United States. Rural area shipping surcharge may apply for remote addresses.
**For all BendPak brand Low-Rise and Mid-Rise Surface Mounted Vehicle Service Lifts (excluding specialty lifts, high rise, commercial parking, material handling, or models for particular purpose) manufactured on or following 7/27/2012.

Limitation of Liability
BendPak/Ranger shall have no obligation pursuant to this Warranty with respect to products which in our sole judgment have been altereddamaged, misused, abused, badly worn, lost or improperly maintained. This Warranty is null and void if the customer or any other person otherthan an authorized representative of BendPak/Ranger has made any attempt to service or modify the tool prior to its return to BendPak/Rangerunder this Warranty. In no event will either party be liable for any damage caused by the other party's failure to fulfill its responsibilities underthese terms and conditions. In no event will either party be liable for any lost profits, lost savings, incidental damage, or other economicconsequential damages. All expressed and implied warranties, including the implied warranties of merchantability and fitness for a particularpurpose, are limited in duration to the coverage period. No warranties, expressed or implied, will apply after this period. BendPak may modifythese terms and conditions at any time by either providing the customer with written notice or posting such revised terms onwww.bendpak.com. Such revised terms shall be effective thirty days from the date of such written notice or posting.

https://bendpakcs.freshdesk.com/a/tickets/new