CALL US TOLL FREE | 9am-6pm EST | M-F
LOCATIONS ACROSS THE NATION | TO SERVE THE ENTIRE COUNTRY
Leading Automotive Equipment Dealer Since 1987
CALL US TOLL FREE | 9am-6pm EST | M-F
LOCATIONS ACROSS THE NATION | TO SERVE THE ENTIRE COUNTRY
Leading Automotive Equipment Dealer Since 1987
Atlas® Platinum XH-PRO8EXT-Combo
To View Atlas 4 Post Cylinder Bleeding Procedure Click Here
(Do this immediately after installation)
The Atlas® Garage Pro 8000 EXT is a true 8,000 LB. four post lift. The Atlas® Garage Pro 8000 EXT incorporates many of the great features of both the Atlas® Garage Pro 8000 and the Atlas® Garage Pro 9000.
Many of our customers drive an SUV or pick up truck and wanted a storage lift that would "go higher" to allow them to park their taller vehicles under the elevated ramps.
Many of our competitors sell "taller" lifts. However, their "taller" lifts also have longer runways. Our customers requested that we make a lift which lifts higher, but does not need to have longer ramps. (Longer ramps take up needed garage space). Most customers want to store a car on top and park a SUV or pick up truck below. There is no need for longer ramps. Our Atlas® Garage Pro 8000 EXT ramps will accommodate a vehicle with a 156 inch wheel base. The Atlas® Garage Pro 8000 EXT has been engineered to provide 79" of clearance UNDER the bottom of the raised runway, but keep the runway length to just less than 14 feet long.
If you need the extra lifting height of the Atlas® Garage Pro 9000, but do not need the extra width and runway length provided by that lift, then the NEW Atlas® Garage Pro 8000 EXT is the perfect choice.
The Atlas® Garage Pro 8000 EXT is capable of lifting your pick up truck or car 84 1/4 inches. This above ground lift is the perfect choice for storing your vehicle. The extended height feature of the Atlas® Garage Pro 8000 EXT Plus makes this lift the perfect choice for parking taller vehicles under stored vehicles.
The Atlas® Garage Pro 8000 EXT comes standard with a powerful 110 volt power unit. A 30 amp breaker is required. The portable Atlas® Garage Pro 8000 EXT includes a caster kit with polyurethane wheels. The caster kit can be installed or removed in just a matter of minutes and requires no tools.
All Atlas® portable four post lifts (8,000 lb. capacity) are designed and built for use by Mr. Homeowner or restoration shop. These lifts are not designed to work in commercial repair shops that raise and lower a lift several times per day. If you have questions about which lift will best suit your application, please contact our sales team.
Supersedes RJ35
The Atlas® PROJACK35 (RJ35) 3500 lbs. capacity sliding hydraulic bridge jack is the perfect choice for the owner of the Atlas® Garage PRO8000 or any of our other Atlas® Garage Pro lifts. The PROJACK35 Sliding Jack will also work on our other hobbyist four post lifts such as the ALI Certified Atlas® APEX8 and APEX9 as well as the Premium Atlas® 408SL and 409HP. The PROJACK35 Sliding Jack is perfect for those who want to perform wheel service on a vehicle that is positioned on top of their four post lift..
Most four post hobbyist lifts come with a jack tray. The jack tray has certain limitations that are eliminated by using the Atlas® PROJACK35 Sliding Jack. The jack tray (with a small floor jack or jack stands) will support ONLY THOSE LIFTING POINTS of the raised vehicle that are between the runways of the four post lift. The RJ35 Sliding Jack has telescoping arms that can be extended over the runways of the four post lift. The lift pads at the end of these arms can be positioned under the LIFTING POINTS (that are located over the runways of the four post lift) of the vehicle allowing the operator to access many more LIFTING POINTS than just using the jack tray.
The Atlas® PROJACK35 Sliding Jack comes standard with a set of peg style truck adapters which increase the lifting height of the lift pads. These truck adapters will allow the Atlas® PROJACK35 Sliding Jack sliding hydraulic jack to raise pick up trucks that will sit higher on the runways than the average passenger car. The Atlas® RJ-35 Sliding Jack is operated by a manual hydraulic pump (porta-power pump) and does not require an air compressor for power. The Atlas® PROJACK35 Sliding Jack sliding hydraulic jack also features two solid locking positions that are used when the vehicle is to be suspended above the runways. When the locking positions of the Atlas® RJ-35 Sliding Jack are engaged, the hydraulic pressure from the lifting cylinder of the RJ-35 Sliding Jack is eliminated. (These locks act much like a pair of jack stands after you lift a vehicle off the ground with a service jack).
Finally, the versatile Atlas® PROJACK35 Sliding Jack is adjustable to fit between the runways of many of the other four post lifts that have been sold in the last several years.
